Water Heater Installation in Murray
Get fast, fair pricing from licensed local pros. Typical Murray cost: $1.1k – $2.5k installed.
- Standard tank install
- $1.1k – $2.5k
- Tankless install
- $2.9k – $6.3k+
- New gas line run
- $375 – $1.3k
- Permit & inspection
- $55 – $375
What's going on with your water heater?
- Licensed& fully insured
- Same-dayservice available
- Upfrontpricing, no pressure
- Localpros, nationwide
Water heater installation cost by job.
Installed-labor pricing for Murray, adjusted for local rates. Relocations and gas-line upgrades add to the base.
In Murray, Utah, water heater installation costs typically range from $850 to $1,900 for a standard tank unit, and $1,900 to $4,700+ for a tankless system. With a median home age of 48 years and cold winter inlet water, many homeowners upgrade to efficient gas models. Local codes require a permit and seismic strapping, and an expansion tank may be needed on closed plumbing systems. Labor and material costs vary with the unit type and any additional gas line work ($325–$1,050).
- Standard tank install (like-for-like)Same fuel, same location$1,050 – $2,500
- Tankless installationWall mount, new venting, larger gas line$2,900 – $6,300+
- Electric-to-gas conversionNew gas line + venting required$2,100 – $5,300
- New gas line runDistance and access drive cost$375 – $1,250
- Permit & inspectionRequired in most jurisdictions$55 – $375
* Relocating the unit or upsizing the gas line adds the most to a base install.
Water heaters in Murray
U.S. Census ACS- Households
- 20,016
- Homeowners
- 13,094
- 62% own
- Median home value
- $415,700
- Median income
- $81,693
- Median home built
- 1978
- Housing units
- 21,301
With a median home built in 1978, many Murray water heaters are at or past their 8–12 year lifespan — a common reason replacements spike here.
What’s different about Murray.
Generic cost pages skip the things that actually decide your price and your unit’s lifespan here — local code, water, and the money you can claim back.
Recommended unit for Murray
Given Utah’s cold semi-arid / high desert climate and gas water heating, high-efficiency gas is the sensible default for most Murray homes. Winter inlet water runs cold here, so recovery rate matters — size up a tankless or favor a high-recovery tank. A pro can confirm the right size and fuel for your home.
Sources: Utah Plumbing Code Ch. 5 Water Heaters (UpCodes, IPC 2021) · P2801.8 Water heater seismic bracing - Utah Residential Code 2021 (ICC) · EIA Utah State Energy Data
What Murray code requires
Replacing a water heater in Murray follows Utah rules under the International Plumbing Code (IPC) / International Residential Code (IRC) under Utah State Construction Code (Title 15A). Here’s what applies statewide:
- PermitRequired
Pulled by your licensed plumber; covers gas/venting and the expansion tank.
- Seismic strappingRequired
State code requires seismic strapping on water heater replacements — budget for it on every quote.
- Expansion tankRequired on closed plumbing systems
Required where a pressure regulator or backflow preventer is present.
- Plumbing codeInternational Plumbing Code (IPC) / International Residential Code (IRC) under Utah State Construction Code (Title 15A)
- Good to know—
Utah is in a seismic zone, so water heaters must be anchored/strapped at the upper and lower one-third; a pan drain is not required on a replacement if one was not previously installed.
Sources: Utah Plumbing Code Ch. 5 Water Heaters (UpCodes, IPC 2021) · P2801.8 Water heater seismic bracing - Utah Residential Code 2021 (ICC) · EIA Utah State Energy Data
Not sure which rules and rebates apply to your home?
A licensed Murray pro will walk you through code, the right unit, and what you can claim back — in one quick call.
No obligation — talk through your options.
Money back in Murray
Utah water heating is mostly gas, which shapes the money back:
- Federal30% of cost, up to $2,000Federal 25C tax credit →
For a qualifying ENERGY STAR heat pump water heater. Claimed on your federal return.
The federal 25C tax credit (30%, up to $2,000 for a qualifying heat pump water heater) applies in every state, including Utah.
Ready to get your water heater fixed in Murray?
Speak with a licensed, insured water heater pro near you. Upfront pricing, same-day availability, no obligation.
- Licensed & insured
- Same-day availability
- Upfront, no-pressure pricing
- Local pros near you
No obligation — talk through your options.
Hot water back in three steps.
- 1
Tell us what’s wrong
Use the cost tool or call — takes 30 seconds. No hot water, a leak, or time for a new unit.
- 2
Get matched with a local pro
We connect you with a licensed, insured water heater specialist near you — often the same day.
- 3
Repair or replace, fast
Your pro confirms the price on-site and gets your hot water back. Most jobs done in a few hours.
Water Heater Installation in Murray, explained.
Why Murray Installation Costs Vary
The main cost drivers in Murray are the unit type (tank vs. tankless), the need for a new gas line, and compliance with Utah's seismic strapping requirements. Older homes may need piping or venting updates. Labor rates reflect local market conditions, and permit fees add a small fixed cost. Choosing a more affordable standard tank over a tankless can lower your upfront expense.
Common Water Heater Issues in Murray
Seismic Strapping Needed
Utah's seismic zone requires water heaters to be anchored at the upper and lower one-third to prevent tipping during earthquakes.
Aging Homes with Outdated Piping
Many Murray homes built around 1978 may have galvanized or undersized gas lines that need upgrading for new installations.
Cold Inlet Water Affecting Recovery
Winter inlet water temperatures in Murray's cold semi-arid climate can slow recovery, making a higher-BTU unit a wise choice.
What to Expect During Installation
A licensed plumber will first obtain the required permit from Murray City. They'll disconnect and remove the old unit, install seismic straps, and connect the new water heater. For gas units, they'll test the gas line and ensure proper venting. The job typically takes 3–6 hours, and final inspection may be required.
Water Heater Installation FAQs — Murray
Yes, a permit is required under the Utah State Construction Code. Your installer should pull the permit and schedule any necessary inspections.
Water Heater Installation near Murray
Get an installation quote.
New install or conversion — compare licensed local pros.